The latest development in the field of cable guides is the Snake. The Snake provides enough space for your power and signal cables to sit comfortably. Pivoting hinges ensure the cables can be gently bent while maintaining a minimum diameter. With the Interlinking one-meter parts, almost any type of base can be configured.

Door de innovatieve buigscharnieren die volledig gebruik maken van een vergrendelingsmechanisme, behoort het heen en weer bewegen van de truss tijdens het omhoog of omlaag hijsen bijna tot het verleden. Het degelijke ontwerp van de Snake, met zijn bronzen lagers, garandeert vele jaren van hoogwaardig gebruik.

The Snake can be mounted onto single tubes, a ladder truss or a triangle truss 30.

A compact aluminum system with a tray width of 5cm. This system is designed for the use of single tubes. The cable guide is available in two different lengths and many different lifting heights.

Basis kabelgeleiders zijn een kosteneffectieve oplossing voor het geleiden van data- en/of stroomkabels op trussconstructies die gehesen zijn. De goot is ongeveer 115 mm breed en kan veel kabels bevatten. De basis kabelgeleider is ontworpen voor gebruik op een 30-er en 40-er truss. Admiral Staging gebruikt 2 mm staal voor de lengteprofielen en de scharnieren zijn voorzien van kogellagers zodat u een leven lang probleemloos ervan gebruik kunt maken.

For higher constructions a base of 4 meter is available. 

The part that make this cable guide a Snake are the unique, innovative  bending hinges which create  the “Snake effect”. These hinges make use of an interlocking mechanism that limits the movement of your truss to a bare minimal while hoisting it up or down. make made up out of several segments, making it possible to route thicker cables through the cable guide. For connecting a bending hinge on each end to a length part you will need 4 aluminium rivets, 4 metal rings and 4 short brass bearings. All these items are separate parts on the Snake item list.

The Snake 1 meter length part has a 68 mm wide gutter which gives you plenty of room to route a lot of cables through. With the Interlinking one-meter parts, almost any type of base can be configured. Pre-drilled holes in the length parts make it easy to assemble the single tube or truss sets.

Sometimes the pre-drilled holes in the black length parts get clotted during the coating process. Use our special Reamer to remove any excess paint from these holes. You can find this handy tool here.

This set contains 2 stacking brackets, 2 anchors and a mouting kit. The stacking brackets are the brackets that support the Snake when it’s folded. You will need 2, 3 or 4 brackets, depending on the height of your snake, to support the weight of the stacked length parts.

2 anchors allow you to anchor your Snake at the top to the ceiling or a tube and at the bottom to your truss or single tube. The pre drilled holes fit a M8 U-bracket, provided in the assembly set, or a M10 bolt.

The mounting kit provided in this set is needed to mount the Snake to a single tube and to anchor it to the ceiling.

In this kit you will find:

For mounting on truss, depending on the truss dimensions you also need the extension set for 30 truss (zink: RIKGSN121 or black: RIKGSN121B) or 40 truss (black: RIKGSN122B).

Stacking too many length parts on top of each other will cause an unstable construction. The stacking brackets are not long enough to provide support when you build a Snake higher than our recommendations. Furthermore, a high stack of elements will block your truss in the upper position. (Not being able to hoist the truss against the ceiling).

The couple set is used to connect the 1 meter length parts. One set exists out of 1 metal plate (placed on the outside of the length part) and 1 metal blockage plate  (placed on the inside of the length part).

This set is only used to connect the straight length parts of your Snake and is NOT used for connecting a length part to the bending hinge!

The aluminium rivet and metal ring that you need to attach the Snake couple set to a length part are separate items on the Snake item list. 

Don’t forget to order our special Reamer when ordering your first Snake parts. Sometimes the pre-drilled holes of the black length parts get clotted in the coating process. The Reamer fits these holes precisely and helps you remove the clotted coating quick and easy.

Rivets are used in combination with brass bearings and metal rings to connect parts of the Snake together. We sell these rivets in a full box of 500 pcs.

Metal rings are used in combination with brass bearings and aluminium rivets  to connect parts of the Snake together. We sell these metal rings in a full box of 500 pcs.

Brass bearings are used to assemble parts of the Snake, ensuring many years of high performance use.

The short bearings are used to connect the bending hinges  and anchor sets to the length parts. You need 4 short brass bearings, 2 on each side of the hinge, to connect the hinge. For securing the anchor set you will need another 4 bearings, 2 for the top and 2 for the bottom anchor. We sell these bearings in a bag of 25 pcs. 

To mount the Snake to a single tube, you need this mounting kit. The kit provides some mounting hooks to attach the Snake to the tube. 

The catch arms, with mounting brackets, are also included in this set. This mounting set is an integral part of the Snake cable guide, independent of the basic length or height.

If a Snake needs to be mounted on a 30 truss, this extension set is necessary. This set provides all the other parts (in addition to the mounting parts that are already included with the Snake) to mount the Snake on a 30 truss.

If a Snake needs to be mounted on a 40 truss, this extension set is necessary. This set provides all the other parts (in addition to the mounting parts that are already included with the Snake) to mount the Snake on a 40 truss.

Basic cable guides are a cost-effective solution for routing data and/or power cables on truss constructions that have been hoisted. The gutter is approximately 115 mm wide and can acommodate many cables. The basic cable guide is designed for use on a 30-er and 40-er truss. Admiral Staging uses 2 mm steel for the length profiles and The hinges come with ballbearings so you get a life time of use without issue. 

For higher constructions a base of 4 meter is also available. With this adapter you can mount your Cable Guide Basic onto your 40 cm truss.